True-Bond™

Directions:

Clean surface of loose aggregates, dirt, grease and oil, and dust. For best results, etch surface with 10 - 15% muriatic acid, flush with clean water and allow to dry. Pour all of container "B" into container "A" and mix thoroughly. Add 3 - 5 parts of dry sand and mix in thoroughly. Brush or trowel on as thick as needed to repair area. Pot life approximately 20 minutes. Because of its high early strength, True-Bond™ may be opened to traffic in six hours.

Small Quantity Mixing

• 2 cups of part "A"
• 1 cup of part "B"
• Stir thoroughly for 1 minute
• Add 9 cups of dry sand (you may use more or less sand to customize the mix for your application!)
• Mix thoroughly again

Coverage: Approximately 200 sq. ft. at approximately ¼" thickness.

Caution:

True-Bond™ Contains an alkaline amine. Avoid contact with skin or eyes. In case of contact, wash skin with soap and water. Flush eyes immediately with water and see doctor. If True-Bond™ is used indoors, provide adequate ventilation.

True-Bond PS™

Bonds and cures on damp surfaces!  A MUST for oily conditions!

Directions:

Clean surface of loose aggregates, dirt, grease and oil, and dust. For best results, etch surface with 10 - 15% muriatic acid and flush with clean water. Pour all of container "B" into container "A" and mix thoroughly. Add 3 - 5 parts of dry sand and mix in thoroughly. Brush or trowel on as thick as needed to repair area. Pot life approximately 20 minutes. Because of its high early strength, True-Bond PS™ may be opened to traffic in six hours.

Small Quantity Mixing

• 2 cups of part "A"
• 1 cup of part "B"
• Stir thoroughly for 1 minute
• Add 9 cups of dry sand (you may use more or less sand to customize the mix for your application!)
• Mix thoroughly again

Coverage: Approximately 200 sq. ft. at approximately ¼" thickness.

Caution:

True-Bond PS™ Contains an alkaline amine. Avoid contact with skin or eyes. In case of contact, wash skin with soap and water. Flush eyes immediately with water and see doctor. If True-Bond PS™ is used indoors, provide adequate ventilation.

True-Bond KOTE™

Directions:

Clean surface of loose aggregates, dirt, grease and oil, and dust. For best results, etch surface with 10 - 15% muriatic acid and flush with clean water. Allow surface to dry. Pour all of container "B" into Container "A". Hand mix thoroughly. Apply with short nap roller, brush or squeegee in a thin, even coat. Pot life approximately 20 minutes. Because of its high early strength, True-Bond Kote™ may be open to traffic in six hours.

Slip Proof Application: For Non-slip finish, broadcast dry sand, aluminum oxide, or carborundum immediately after application (while True-Bond Kote is still wet). When material is dry, sweep off excess aggregate and apply optional second coat (with or without aggregate).

Coverage: Approximately 300 sq. ft. per kit.

Small Quantity Mixing

• 2 cups of part "A"
• 1 cup of part "B"
• Stir thoroughly

Caution:

True-Bond KOTE™ Contains an alkaline amine. Avoid contact with skin or eyes. In case of contact, wash skin with soap and water. Flush eyes immediately with water and see doctor. If True-Bond KOTE™ is used indoors, provide adequate ventilation.

True-Bond LLT™

Directions:

Clean surface of loose aggregates, dirt, grease and oil, and dust. For best results, etch surface with 10 - 15% muriatic acid and flush with clean water and allow to dry. Pour all of container "B" into container "A" and mix thoroughly. Add 3 - 5 parts of dry sand and mix in thoroughly. Brush or trowel on as thick as needed to repair area. Pot life approximately 20 minutes. Because of its high early strength, True-Bond LLT™ may be opened to traffic in six hours.

Small Quantity Mixing

• 2 cups of part "A"
• 1 cup of part "B"
• Stir thoroughly for 1 minute
• Add 9 cups of dry sand (you may use more or less sand to customize the mix for your application!)
• Mix thoroughly again

Coverage: Approximately 200 sq. ft. at approximately ¼" thickness.

Caution:

True-Bond LLT™ Contains an alkaline amine. Avoid contact with skin or eyes. In case of contact, wash skin with soap and water. Flush eyes immediately with water and see doctor. If True-Bond LLT™ is used indoors, provide adequate ventilation.

True-Bond CR™

Directions:

Clean surface of loose aggregates, dirt, grease and oil, and dust. For best results, etch surface with 10 - 15% muriatic acid, flush with clean water and allow to dry. Pour all of container "B" into container "A" and mix thoroughly. Add 3 - 5 parts of dry sand and mix in thoroughly. Brush or trowel on as thick as needed to repair area. Pot life approximately 20 minutes. Because of its high early strength, True-Bond CR™ may be opened to traffic in six hours.

Small Quantity Mixing

• 2 cups of part "A"
• 1 cup of part "B"
• Stir thoroughly for 1 minute
• Add 9 cups of dry sand (you may use more or less sand to customize the mix for your application!)
• Mix thoroughly again

Coverage: Approximately 200 sq. ft. at approximately ¼" thickness.

Caution:

True-Bond CR™ Contains an alkaline amine. Avoid contact with skin or eyes. In case of contact, wash skin with soap and water. Flush eyes immediately with water and see doctor. If True-Bond CR™ is used indoors, provide adequate ventilation.

True-Bond CT™

Directions:

Clean surface of loose aggregates, dirt, grease and oil, and dust. For best results, etch surface with 10 - 15% muriatic acid and flush with clean water and allow to dry. Combine all of container "A" with container "B" and mix thoroughly. Add 3 to 5 parts of dry sand and mix in thoroughly. Brush or trowel on as thick as needed to repair area. Pot life approximately 20 minutes. Because of its high early strength, True-Bond CT™ may be open to traffic in six hours.

Small Quantity Mixing

• 1 cup of part "A"
• 1 cup of part "B"
• Stir thoroughly for 1 minute
• Add 6 cups of dry sand (you may use more or less sand to customize the mix for your application!)
• Mix thoroughly again

Coverage: Approximately 200 sq. ft. at approximately ¼" thickness.

Caution:

True-Bond CT™ Contains an alkaline amine. Avoid contact with skin or eyes. In case of contact, wash skin with soap and water. Flush eyes immediately with water and see doctor. If True-Bond CT™ is used indoors, provide adequate ventilation.

True-Bond Gel™

Directions:

Clean surface of loose aggregates, dirt, grease and oil, and dust. For best results, etch surface with 10 - 15% muriatic acid, flush with clean water and allow to dry. Combine all of container "A" with container "B" and mix thoroughly. Add 1 to 5 parts of dry sand and mix in thoroughly. Trowel on as thick as needed to repair area. Pot life approximately 20 minutes. Because of its high early strength, True-Bond GEL™ may be open to traffic in six hours.

Small Quantity Mixing

• 1 cup of part "A"
• 1 cup of part "B"
• Stir thoroughly for 1 minute
• Add 2 cups of dry sand (you may use more or less sand to customize the mix for your application!)
• Mix thoroughly again

Coverage: Approximately 200 sq. ft. at approximately ¼" thickness.

Caution:

True-Bond GEL™ Contains an alkaline amine. Avoid contact with skin or eyes. In case of contact, wash skin with soap and water. Flush eyes immediately with water and see doctor. If True-Bond GEL™ is used indoors, provide adequate ventilation.

Sure-Foot™

Directions:

Clean floors by acid etching with 15% muriatic acid removing surface grease, acid, oil, etc. Remove components A, B and C from mixing pail. Blend part A and B for 3 to 5 minutes. Then add aggregate and mix well. Then spread a thin, uniform coating with a squeegee, trowel, brush or short nap roller. Level all puddles. Tack free in 1 hour @ 70 degrees Fahrenheit, ready for full traffic in 6 hours.

300 SQ FT Kit: Two containers Part A, two containers Part B and 4 lbs. Part C, aggregate.